Complete specifications for the McCormick Farmall 460, Farmall 560 and International 560 tractors, transcribed from the specifications section of the factory operator's manual (form 1 014 051 R3) published by International Harvester. One book covers five tractors: the Farmall 460 and 560 row-crop tractors, the high-clearance Hi-Clear version of each, and the standard-tread International 560. All are six-cylinder tractors governed to 1,800 rpm, sharing a 3-9/16 in. bore; the 560 has the longer 4-3/8 in. stroke. International Harvester built the 460 and 560 from 1958 to 1963.
The ground speed tables at the bottom of the page list every tire option the manual gives, in both normal and Torque Amplifier (T.A.) range, so you can find the speeds for the tires actually on your tractor.
Engine
| Specification | Farmall 460 | Farmall 560 | International 560 |
|---|---|---|---|
| Cylinders | 6 | ||
| Bore | 3-9/16 in. | ||
| Stroke | 3-11/16 in. | 4-3/8 in. | 4-3/8 in. |
| Minimum Idle (Governed) | Approx. 425 rpm | ||
| Maximum Idle (No Load) | Approx. 1980 rpm | ||
| Maximum (Full Load) | 1,800 rpm | ||
| Battery Ignition Unit | IH, 30° advance distributor (gasoline engine; distillate or kerosene engine) | ||
| Spark Plug Gap | 0.023 in. | ||
| Valve Clearance (Engine Hot) | 0.027 in. | ||
| Carburetor (with Donaldson Air Cleaner) | IH 1-1/4 in., updraft | ||
Capacities
U.S. measure.
| Specification | Farmall 460 & 460 Hi-Clear | Farmall 560 & 560 Hi-Clear | International 560 |
|---|---|---|---|
| Cooling System | 19 qt. | 19-1/2 qt. | 19-1/2 qt. |
| Fuel Tank | 33 gal. | ||
| Crankcase | 9 qt. | ||
| Transmission and Differential (also Hydra-Touch Reservoir) | Approx. 10 gal. | Approx. 16 gal. | Approx. 16 gal. |
| Steering Gear Housing | 2-1/2 pt. | 2-1/2 pt. | 3-1/2 pt. |
| Air Cleaner Oil Cup | 2-1/4 pt. | 2 pt. | 2 pt. |
| Rear Axle Drive Housing, Each (Hi-Clear) | 3 qt. | 3 qt. | — |
| Independent PTO Housing | 2 qt. | ||
Clutch & Brakes
| Specification | Farmall 460 | Farmall 560 | International 560 |
|---|---|---|---|
| Clutch, Single-Plate Dry-Disc, Spring-Loaded | 10-1/2 in. | 12 in. | 12 in. |
| Clutch, Single-Plate Dry-Disc, Over-Center | — | — | 12 in. |
| Foot Brakes | Mechanical disc type, operated individually or interlocked | ||
Electrical
| System | 12-volt |
|---|---|
| Fuse | AGC-10 amp. |
| Headlight | Sealed unit, 12-16 volt |
| Combination Rear Light and Tail Light | 12-16 volt |
Independent Power Take-Off
PTO shaft speeds in rpm.
| Engine Speed | Planetary-Type, 460 & 460 HC | Planetary-Type, 560, 560 HC & Int. 560 | Clutch-Type, 460 & 460 HC | Clutch-Type, 560s |
|---|---|---|---|---|
| Maximum Full Load (1800 rpm) | 556 | 538 | 547 | 540 |
| Low Idle (425 rpm) | 131 | 127 | 129 | 128 |
| Fast Idle (1980 rpm) | 612 | 592 | 602 | 594 |
Belt Pulley
| Specification | Farmall 460 | Farmall 560 | International 560 |
|---|---|---|---|
| Side-mounted (T.A. handle forward, disengaged) | |||
| Low Idle | 263 rpm | 263 rpm | 263 rpm |
| Fast Idle | 1,223 rpm | 1,227 rpm | 1,227 rpm |
| Maximum Full Load | 1,112 rpm | 1,115 rpm | 1,115 rpm |
| Belt Speed, 11 in. Pulley at Full Load | 3,202 ft./min. | 3,212 ft./min. | 3,212 ft./min. |
| Rear-mounted, planetary-type | |||
| Low / Fast Idle / Max. Full Load | 255 / 1,186 / 1,078 rpm | 246 / 1,146 / 1,042 rpm | 246 / 1,146 / 1,042 rpm |
| Belt Speed | 3,104 ft./min. | 2,999 ft./min. | 2,999 ft./min. |
| Rear-mounted, clutch-type | |||
| Low / Fast Idle / Max. Full Load | 250 / 1,165 / 1,059 rpm | 247 / 1,151 / 1,046 rpm | 247 / 1,151 / 1,046 rpm |
| Belt Speed | 3,051 ft./min. | 3,013 ft./min. | 3,013 ft./min. |
| All pulleys | |||
| Diameter | 11 in. | ||
| Face | 7-1/2 in. | ||
Tires & Tread
Inches unless noted.
| Specification | Farmall 460 | Farmall 460 Hi-Clear | Farmall 560 | Farmall 560 Hi-Clear | International 560 |
|---|---|---|---|---|---|
| Front Tire | 5.50-161 | 6.00-201 | 6.00-161 | 6.00-201 | 6.50-18 |
| Rear Tire | 12.4-38 (11-38)1 | 11-381 | 13.6-38 (12-38)1 | 13-381 | 14-301 |
| Front Tread | 8, 16 | 60 to 90 | 9, 16 | 60 to 90 | 51 |
| Front Tread, Adjustable Axle | 57 to 89 | — | 58 to 90 | — | — |
| Rear Tread, Double-Bead Rim | 48 to 93 | 62 to 74 | 50 to 94 | 62 to 74 | 58 to 70 |
| Rear Tread, Power-Adjusted Wheels | 48 to 97 | — | 50 to 100 | — | — |
| Wheelbase | 95 | 100 | 96 | 100 | 85-1/2 |
General Dimensions
Inches unless noted.
| Specification | Farmall 460 | Farmall 460 Hi-Clear | Farmall 560 | Farmall 560 Hi-Clear | International 560 |
|---|---|---|---|---|---|
| Length | 140 | 153 | 141 | 155 | 146 |
| Width, Minimum (Rear Axle Outside Edge) | 83-1/2 | 86 | 85 | 86 | 72 |
| Width, Maximum (Rear Tires) | 105 | — | 107 | 88 | 86 |
| Height to Steering Wheel | 78 | 90 | 79 | 92 | 71 |
| Crop clearance | |||||
| Under Front Axle (Wide Axle) | 22 | 34 | 22-1/2 | 34 | 15 |
| Under Frame | 19-1/2 | 30-1/2 | 18-1/2 | 29-5/82 | 16 |
| Under Rear Axle | 25-1/2 | 35-1/4 | 26-1/4 | 36 | — |
| Drawbar | |||||
| Height, Quick-Attachable Drawbar | 15 to 20 | 15, 18, 21 | 15 to 21 | 17, 20, 23 | 12, 15, 17 |
| Height, Heavy-Duty Fixed Drawbar | — | 25-1/2 | — | 28 | — |
| Height, Swinging Drawbar (Quick-Attachable) | 13 to 20 | — | 14 to 21 | — | 9, 13, 16 |
| Lateral Adjustment, Each Side of Center Hole | 13 | 15 | 13 | 15 | 9 |
| Swinging Drawbar Lateral Swing, Each Side | 18 | — | 16 | — | 14 |
| Minimum turning radius | |||||
| Without Brake | 9-1/2 ft. | 14-1/2 ft. | 9 ft. | 14-1/2 ft. | 14 ft. |
| With Brake | 9 ft. | 12 ft. | 8-1/2 ft. | 12 ft. | 12 ft. |
Standardized Hitch Dimensions
Inches. Based on 12.4-38 (11-38) tires for the Farmall 460, 12-38 for the Farmall 560 and 14-30 for the International 560.
| Specification | Farmall 460 | Farmall 460 Hi-Clear | Farmall 560 | Farmall 560 Hi-Clear | International 560 |
|---|---|---|---|---|---|
| Drawbar Hitch Hole to End of PTO Shaft, Horizontal (Fixed and Swinging Drawbars) | 14 | — | 14 | — | 144 |
| Same, Hi-Clear Fixed Drawbar | — | 16-1/23 | — | 16-1/23 | — |
| Same, Hi-Clear Heavy-Duty Fixed Drawbar | — | 53 | — | 53 | — |
| Height of PTO Shaft Above Ground | 25-1/2 | 37-1/83 | 27 | 39-3/83 | 24-3/84 |
| Drawbar Hitch to PTO Shaft, Vertical5 | 11-1/8 | 11-1/8 | 11-5/8 | 11-5/8 | 9-3/84 |
| Height of Drawbar Hitch Hole Above Ground5 | 14-3/8 | 14-3/8 | 15-1/4 | 15-1/4 | 15-1/44 |
Ground Speeds, Farmall 460 & 460 Hi-Clear
Miles per hour at rated 1,800 engine rpm. R-1 is agricultural tread; R-2 is cane or rice tread.
| Gear | 460 R-1 12.4-38 (11-38)6 |
460 R-1 13.6-38 (12-38) |
460 R-2 11-38 |
460 R-2 12-38 |
460 R-2 13-38 |
460 HC R-1 12.4-38 (11-38) |
460 HC R-1 13.6-38 (12-38) |
460 HC R-2 11-386 |
460 HC R-2 12-38 |
460 HC R-2 13-38 |
|---|---|---|---|---|---|---|---|---|---|---|
| 1st, Normal | 2.6 | 2.6 | 2.6 | 2.7 | 2.8 | 2.4 | 2.5 | 2.5 | 2.5 | 2.6 |
| 1st, T.A. | 1.7 | 1.8 | 1.8 | 1.8 | 1.9 | 1.6 | 1.7 | 1.7 | 1.7 | 1.8 |
| 2nd, Normal | 3.9 | 4.0 | 4.0 | 4.1 | 4.3 | 3.7 | 3.8 | 3.8 | 3.9 | 4.0 |
| 2nd, T.A. | 2.7 | 2.7 | 2.7 | 2.8 | 2.9 | 2.5 | 2.6 | 2.5 | 2.6 | 2.7 |
| 3rd, Normal | 5.3 | 5.4 | 5.4 | 5.5 | 5.7 | 5.0 | 5.1 | 5.1 | 5.2 | 5.4 |
| 3rd, T.A. | 3.6 | 3.7 | 3.6 | 3.7 | 3.9 | 3.4 | 3.5 | 3.4 | 3.5 | 3.7 |
| 4th, Normal | 7.5 | 7.7 | 7.6 | 7.8 | 8.1 | 7.1 | 7.3 | 7.2 | 7.4 | 7.7 |
| 4th, T.A. | 5.1 | 5.2 | 5.2 | 5.3 | 5.5 | 4.8 | 4.9 | 4.9 | 5.0 | 5.2 |
| 5th, Normal | 16.6 | 17.0 | 16.9 | 17.3 | 17.9 | 15.6 | 16.0 | 15.9 | 16.3 | 16.9 |
| 5th, T.A. | 11.2 | 11.5 | 11.4 | 11.7 | 12.1 | 10.6 | 10.8 | 10.8 | 11.0 | 11.4 |
| Reverse, Normal | 3.2 | 3.3 | 3.3 | 3.3 | 3.5 | 3.0 | 3.1 | 3.1 | 3.2 | 3.3 |
| Reverse, T.A. | 2.2 | 2.2 | 2.2 | 2.3 | 2.3 | 2.0 | 2.1 | 2.1 | 2.1 | 2.2 |
Ground Speeds, Farmall 560 & 560 Hi-Clear
Miles per hour at rated 1,800 engine rpm.
| Gear | 560 R-1 13.6-38 (12-38) / 15.5-386 |
560 R-1 12.4-38 (11-38) |
560 R-2 11-38 |
560 R-2 12-38 |
560 R-2 13-38 |
560 HC R-2 12-38 |
560 HC R-2 13-38 |
|---|---|---|---|---|---|---|---|
| 1st, Normal | 2.2 | 2.1 | 2.2 | 2.2 | 2.3 | 2.1 | 2.2 |
| 1st, T.A. | 1.5 | 1.4 | 1.5 | 1.5 | 1.5 | 1.4 | 1.5 |
| 2nd, Normal | 3.8 | 3.7 | 3.8 | 3.9 | 4.0 | 3.7 | 3.8 |
| 2nd, T.A. | 2.6 | 2.5 | 2.6 | 2.6 | 2.7 | 2.5 | 2.6 |
| 3rd, Normal | 5.4 | 5.2 | 5.3 | 5.5 | 5.7 | 5.2 | 5.4 |
| 3rd, T.A. | 3.6 | 3.5 | 3.6 | 3.7 | 3.8 | 3.5 | 3.6 |
| 4th, Normal | 7.5 | 7.3 | 7.4 | 7.6 | 7.9 | 7.2 | 7.5 |
| 4th, T.A. | 5.0 | 4.9 | 5.0 | 5.1 | 5.3 | 4.8 | 5.0 |
| 5th, Normal | 16.6 | 16.2 | 16.5 | 16.9 | 17.6 | 16.0 | 16.6 |
| 5th, T.A. | 11.2 | 11.0 | 11.1 | 11.4 | 11.9 | 10.8 | 11.2 |
| Reverse, Normal | 2.8 | 2.8 | 2.8 | 2.9 | 3.0 | 2.7 | 2.8 |
| Reverse, T.A. | 1.9 | 1.9 | 1.9 | 1.9 | 2.0 | 1.8 | 1.9 |
| With high-speed low and reverse gears | |||||||
| 1st, high-speed low gear, Normal | 2.5 | 2.4 | 2.5 | 2.5 | 2.6 | 2.4 | 2.5 |
| 1st, high-speed low gear, T.A. | 1.97 | 1.6 | 1.7 | 1.7 | 1.8 | 1.6 | 1.7 |
| Reverse, high-speed reverse gear, Normal | 3.3 | 3.2 | 3.3 | 3.4 | 3.5 | 3.2 | 3.3 |
| Reverse, high-speed reverse gear, T.A. | 2.2 | 2.2 | 2.2 | 2.3 | 2.4 | 2.1 | 2.2 |
Ground Speeds, International 560
Miles per hour at rated 1,800 engine rpm. R-3 is industrial tread.
| Gear | R-3 14-26 | R-1 14-306 | R-1 15-30 | R-2 15-30 | R-3 18-26 (DN-20-26 rims) | R-2 18-26 (DN-20-26 rims) |
|---|---|---|---|---|---|---|
| 1st, Normal | 1.9 | 2.1 | 2.2 | 2.2 | 2.2 | 2.4 |
| 1st, T.A. | 1.3 | 1.4 | 1.5 | 1.5 | 1.5 | 1.6 |
| 2nd, Normal | 3.4 | 3.7 | 3.9 | 4.0 | 3.8 | 4.2 |
| 2nd, T.A. | 2.3 | 2.5 | 2.7 | 2.7 | 2.6 | 2.8 |
| 3rd, Normal | 4.8 | 5.2 | 5.5 | 5.6 | 5.3 | 5.9 |
| 3rd, T.A. | 3.2 | 3.5 | 3.7 | 3.8 | 3.6 | 4.0 |
| 4th, Normal | 6.7 | 7.3 | 7.7 | 7.7 | 7.4 | 8.2 |
| 4th, T.A. | 4.5 | 4.9 | 5.2 | 5.2 | 5.0 | 5.5 |
| 5th, Normal | 14.8 | 16.2 | 17.1 | 17.3 | 16.6 | 18.2 |
| 5th, T.A. | 10.0 | 10.9 | 11.6 | 11.6 | 11.2 | 12.3 |
| Reverse, Normal | 2.5 | 2.7 | 2.9 | 2.9 | 2.8 | 3.1 |
| Reverse, T.A. | 1.7 | 1.9 | 2.0 | 2.0 | 1.9 | 2.1 |
| With high-speed low and reverse gears | ||||||
| 1st, high-speed low gear, Normal | 2.2 | 2.4 | 2.6 | 2.6 | 2.5 | 2.7 |
| 1st, high-speed low gear, T.A. | 1.5 | 1.6 | 1.7 | 1.7 | 1.7 | 1.8 |
| Reverse, high-speed reverse gear, Normal | 3.0 | 3.2 | 3.4 | 3.4 | 3.3 | 3.6 |
| Reverse, high-speed reverse gear, T.A. | 2.0 | 2.2 | 2.3 | 2.3 | 2.2 | 2.4 |
Notes:
1 The manual marks these sizes to show that other pneumatic tire sizes were available, as well as steel rear wheels for all tractors except the Hi-Clear.
2 The fraction is hard to read in the source scan. TODO: confirm.
3 The manual notes that Farmall Hi-Clear tractors have standard PTO shafts but do not conform fully to A.S.A.E. standards, because of their high-clearance construction. TODO: the two Hi-Clear drawbar rows are read as applying to both Hi-Clear tractors; confirm against the scan.
4 International 560 figures are when using a drawbar extension plate on top of the drawbar, with the drawbar in the middle position. TODO: column alignment of the last two rows is hard to read in the scan; confirm.
5 Fixed drawbar with the extension plate on top, in the lowest position.
6 The manual notes that the ground speeds shown on the tachometer dial correspond to this column.
7 As printed. Every other figure in this row runs about 1.6 to 1.8; 1.9 may be a misprint.
All specifications transcribed from the specifications section of the McCormick Farmall 460, 560 and International 560 Tractors operator's manual, form 1 014 051 R3, originally published by International Harvester Company. The manual states that specifications are subject to change without notice; verify against your tractor's serial number before ordering parts or setting clearances.
Need the complete Farmall 460 and 560 operator's manual?
Get the full 68-page manual as an instant PDF download: controls, Torque Amplifier and Hydra-Touch operation, independent PTO, belt pulley, wheels and weights, lubrication, and the specifications reproduced above.