Massey Ferguson MF 2675 & 2705 Tractor Specifications

Specs Hub › Massey Ferguson › MF 2675 & 2705

Factory specifications for the Massey Ferguson MF 2675 and MF 2705 row-crop tractors, transcribed from the original operator's manual (Massey Ferguson publication 1448 510 M1, printed 7/79). Both are 2000 Series machines built from 1978 into the early 1980s: the MF 2675 runs the naturally aspirated Perkins A6.354.4 six-cylinder diesel, while the MF 2705 uses the turbocharged AT6.354.4. Where a figure differs between the two models it is shown for each.

 

Engine

Type	MF 2675 — Perkins A6.3544 (naturally aspirated); MF 2705 — Perkins AT6.3544 (turbocharged); direct injection
Cylinder bore	98.4 mm (3.875 in)
Piston stroke	127 mm (5 in)
Total displacement	5.8 litres (354 cu. in)
Compression ratio	16:1
Firing order	1-5-3-6-2-4
Low idle	750 ± 25 rpm
Maximum full-load speed	2500 rpm
High idle	2680–2780 rpm

Fuel System

Type	Gravity flow and pressure fed
Filters	Two full-flow with replaceable elements
Fuel injectors	Multi-hole type

Electrical System

Batteries	Two 12-volt, 95 amp. hr., negative ground
Starter switch	Key operated
Starter	12-volt, 4 pole
Alternator	Continuous output, diode-rectified A.C. type with built-in solid-state regulator

Brakes

Type (power assist)	Single disc, 412.8 mm (16-1/4 in) wet brakes — automatically filled reservoir

Hydraulic System

Type	Dual hydraulic gear pump — one circuit for the 3-point hitch, steering and auxiliary hydraulic service, and a second circuit for pressure lubrication to the transmission, Multi-Power clutches, IPTO clutch and tractor brake cooling
Main pump	Main section (steering, 3-point linkage, 3rd-spool auxiliary): 59.8 L/min (15.8 gpm). Low-pressure section (IPTO clutch, transmission, etc.): 21.2 L/min (5.6 gpm)
Auxiliary pump	Mounts in L.H. cover — 59.8 L/min (15.8 gpm)
Implement control (linkage models only)	Draft control and position control
Auxiliary hydraulics	(1) Two-spool valve on the left-hand side (with auxiliary pump), automatic return from detent; or (2) two-spool valve on the left-hand side plus one spool on the right for three independent circuits, automatic return from detent

Power Train

Clutch	355.6 mm (14 in) dia., single disc, foot operated
Transmission	8-speed manual with manual shuttle in the first six speeds; or 24-speed with hydraulic shift between 3 speeds in each of the 8 manually selected gears, plus a forward-to-reverse shuttle in 6 speeds

Fluid Capacities

Fuel tank	329.3 L (87 U.S. / 72.4 Imp. gal)
Cooling system	29.3 L (31 U.S. / 25.8 Imp. qt)
Crankcase with filter change	MF 2675 (1 filter) — 17 L (18 U.S. / 15 Imp. qt); MF 2705 (2 filters) — 18 L (19 U.S. / 15.8 Imp. qt)
Transmission & rear axle — with filters	113.5 L (30 U.S. / 25 Imp. gal)
Transmission & rear axle — without filters	106 L (28 U.S. / 23 Imp. gal)

Dimensions & Weight

Wheelbase	268 cm (105.4 in)
Overall length	450 cm (177 in)
Overall height (top of cab)	284.7 cm (112 in)
Overall width	239 cm (94.1 in) standard axle; 300 cm (118.1 in) long axle
Tread widths	See page 65 of the operator's manual
Turning radius (without brakes)	Approx. 457.5 cm (15 ft)
Minimum ground clearance (24.5-32 tires)	39.6 cm (15.6 in)1
Shipping weight, minimum — cab model	MF 2675 — 4990 kg (11,000 lb); MF 2705 — 5080 kg (11,200 lb)
Shipping weight, minimum — platform model	MF 2675 — 4647 kg (10,244 lb); MF 2705 — 4792 kg (10,564 lb)
Maximum operating weight	8618 kg (19,000 lb)

Power Take-Off

PTO operating speed	540 rpm PTO at 1990 engine rpm; 1000 rpm PTO at 2090 engine rpm
Rated PTO horsepower	MF 2675 — 74 kW (100 hp) at 2500 engine rpm; MF 2705 — 89 kW (120 hp) at 2500 engine rpm

All specifications transcribed from the Massey Ferguson MF 2675 / 2705 Operator's Manual (publication 1448 510 M1, printed 7/79). Figures are as published by the manufacturer and are provided for reference.
¹ Minimum ground clearance is corrected to 39.6 cm; the original printing shows "396 cm (15.6 inches)," a dropped-decimal typo (15.6 in = 39.6 cm).