Bobcat 700 & 720 Skid Steer Loader Specifications

Specs Hub › Bobcat 700 Series › 700 & 720

Complete specifications for the Bobcat 700 and 720 skid steer loaders, transcribed from the technical data section of the Clark Melroe factory service manual (6556619). The manual covers the two models on one specification sheet: both use the air-cooled Wisconsin VH4D four-cylinder gasoline engine rated at 28 horsepower, with twin hydrostatic drives, #80 chain final drives and a 1200 lb. rated operating capacity.

Operational & Performance

Operational & Performance
Operating Weight 4400 lbs. (1920 kg)1
Rated Operating Capacity 1200 lbs. (544 kg)
Lift Capacity to Maximum Height 2342 lbs. (1063 kg)
Tipping Load 2400 lbs. (1089 kg)
Raise to Maximum Height 4.7 seconds
Lower from Maximum Height 2.8 seconds
Dump Bucket 1.4 seconds
Rollback Bucket 1.4 seconds
Travel Speed, Work Range Infinitely variable, 0 to 4.2 mph (6.76 km/h)
Travel Speed, Transport Range Infinitely variable, 0 to 6.3 mph (10.1 km/h)

Controls

Controls
Vehicle Steering, direction and speed controlled by two hand levers and a hand grip range selector. The hydrostatic transmissions provide braking.
Loader Lift, tilt and auxiliary functions controlled by separate foot pedals
Engine Hand lever throttle, manual choke and key-type starter switch
Main Drive Hydrostatic

Engine

Engine
Make / Model Wisconsin VH4D
Type Valve in block, gasoline
Number of Cylinders 4
Bore / Stroke 3.25 in. / 3.25 in. (82.55 mm / 82.55 mm)2
Displacement 107.7 cu. in. (1.76 liters)3
Governed Flywheel Horsepower 28 hp @ 2500 rpm
Maximum Torque 66.2 ft.-lbs. (89.8 N·m) @ 1800 rpm
Firing Order 1-3-4-2
Maximum RPM (Full Load) 2550 rpm4
Idle RPM (Minimum) 1000–1200 rpm
Idle RPM (Maximum) 2500 rpm
Cooling Air
Lubrication Pressure spray
Crankcase Vent Internal breathing
Air Cleaner Replaceable dry cartridge type with condition indicator
Fuel Regular gasoline, 85–90 octane

Engine Tune-Up & Clearances

Engine Tune-Up & Clearances
Valve Tappet Clearance, Intake 0.008 in. (0.203 mm)
Valve Tappet Clearance, Exhaust 0.016 in. (0.406 mm)
Valve Stem Clearance in Guide 0.003–0.005 in. (0.076–0.127 mm); maximum 0.007 in. (0.178 mm)
Breaker Point Gap 0.018–0.022 in. (0.458–0.559 mm)
Spark Plug Gap 0.030 in. (0.762 mm)
Distributor Advance Automatic: 11-1/2° in the distributor (23° at the crankshaft), fully advanced at 1800 rpm
Crank Pin Diameter 1.875–1.876 in. (47.625–47.650 mm)
Crankshaft End Play (cold) 0.002–0.004 in. (0.051–0.102 mm)
Connecting Rod to Crank Pin (diameter) 0.0012–0.0033 in. (0.030–0.086 mm)
Connecting Rod Side Clearance 0.009–0.018 in. (0.229–0.457 mm)
Piston to Cylinder at Skirt 0.0035–0.0040 in. (0.089–0.102 mm)
Piston Ring Gap 0.010–0.020 in. (0.254–0.508 mm)
Starter 12-volt gear drive, negative ground

Engine Torque Specifications

Engine Torque Specifications
Item ft.-lbs. N·m
Cylinder Head Bolts 22–24 30–33
Spark Plug 25–30 34–41
Manifold Nuts 18–23 24–31
Timing Gear Cover 14–18 19–24
Oil Pan Bolts 6–9 8–12
Connecting Rod Bolts 22–28 30–38
Cylinder Block Nuts 40–50 54–68
Main Bearing Plate Bolts 25–30 34–41
Flywheel Nut 75 101.7
Alternator Sheave Nuts 40–60 54–81
Drive Coupling to Flywheel Nuts 30–35 40–47

Engine Oil Viscosity

Choose by the temperature range expected before the next oil change. The manual says to use summer recommendations in winter if the machine is kept in a warm building.5

Engine Oil Viscosity
API Service Class SE for gasoline engines; CD for diesel engines
SAE 10W-30 / 10W-40 −10°F (−23°C) and above
SAE 15W-40 About +5°F (−15°C) and above
SAE 5W-30 Below +60°F (+15°C)
SAE 30 +50°F (+10°C) and above
SAE 20W / 20 +15°F to +70°F (−9°C to +21°C)
SAE 10W Below +40°F (+4°C)

Loader Hydraulics

Loader Hydraulics
Pump Engine driven, vane type
System Relief Pressure 2100 psi (14,479 kPa)
Cylinders Double-acting
Valves Open-centre type with float detent on lift
Fluid Lines SAE standard full-flow tubes, hoses and fittings
Hydraulic Cylinders
Cylinder Bore Rod Stroke
Lift 2.00 in. (50.80 mm) 1.25 in. (31.75 mm) 25.90 in. (657.86 mm)
Tilt 2.00 in. (50.80 mm) 1.00 in. (25.40 mm)6 16.60 in. (419.10 mm)7

Power Train

Power Train
Transmission Two infinitely variable, fully reversing hydrostatic
Reduction Ratio, High Range Infinite to 24.3:1
Reduction Ratio, Low Range Infinite to 46.5:1
Final Drive #80 roller chain running in a sealed oil bath

Electrical

Electrical
Alternator Enclosed, belt driven, 22 amp
Battery 12-volt, 70 amp-hour rating
Starter 12-volt gear drive

Capacities

Capacities
Fuel Tank, Steel 13.5 gal. (51.10 liters)
Fuel Tank, Plastic 16.5 gal. (62.46 liters)
Engine Oil, Including Filter 4 qt. (3.8 liters)

Tires & Floor Pressure

Tires & Floor Pressure
Standard Tires 7.00 × 15, 6-ply rating
Tire Pressure 50 psi (345 kPa)
Floor Pressure
Floor Pressure, psi (kPa) Front Rear
Standard Tires, Rated Load 44.8 (309) 37.9 (261)
Standard Tires, Unloaded 34.8 (240) 42.7 (294)
Flotation Tires, Rated Load 26.6 (183) 22.1 (152)
Flotation Tires, Unloaded 20.9 (144) 25.5 (176)

Dimensions

With dirt bucket. Dimensions may vary with other bucket types. Inches with millimetres in parentheses, as printed on the manual's dimension drawing.

Dimensions
Overall Operating Height (bucket fully raised) 139 in. (3531 mm)
Height to Bucket Hinge Pin (fully raised) 109 in. (2769 mm)
Dump Height 86 in. (2184 mm)
Dump Reach 20 in. (508 mm)
Height to Top of Operator Guard 81 in. (2057 mm)
Length without Bucket 89 in. (2261 mm)
Length with Bucket 114 in. (2896 mm)
Wheelbase 35 in. (889 mm)
Width over Bucket 55 in. (1397 mm)
Width over Tires 53.5 in. (1359 mm)
Tread Width (wheel centres) 46 in. (1168 mm)
Ground Clearance 8 in. (203 mm)
Turning Clearance Radius, Front (with bucket) 67 in. (1702 mm)
Turning Clearance Radius, Rear 54 in. (1372 mm)
Maximum Dump Angle 36°
Bucket Rollback at Ground 26°
Bucket Rollback in Carry Position 45°
Departure Angle (rear) 26°

Notes:
1 Printed as “4400 lbs. (1920 kg)”. 4400 lb is about 1996 kg and 1920 kg is about 4233 lb, so one of the two figures is off. Both are shown as printed; the 722 page gives 4400 lbs. (2000 kg).
2 The engine specification page prints bore and stroke as “3.25 (82,55 liters)”, a typesetting slip for millimetres.
3 The loader page prints “107.7 cu. in. (1,765 l)”, using a decimal comma; the engine specification page gives 1.76 liters.
4 The manual lists “Maximum RPM (Full Load) 2550”, “Idle RPM (Minimum) 1000–1200” and “Idle RPM (Maximum) 2500”, shown here as printed. Governed horsepower is rated at 2500 rpm.
5 The viscosity ranges are read from the bar chart on the engine specification page (PI-2358), which is the same for all three engines. The end points are approximate.
6 The 700/720 page prints the tilt rod as “1 (35,4)”. 1 in. is 25.4 mm, and the 721 and 722 pages print 25.40, so 35,4 is a misprint.
7 Printed as 16.6 in. (419.10 mm) for all models. 419.10 mm is exactly 16.5 in.; 16.6 in. would be about 421.6 mm. Both figures are shown as printed.
All specifications transcribed from the Bobcat 700, 720, 721, 722 Loader Service Manual (6556619), pages 8A-1 to 8A-3, published by Clark Equipment Company, Melroe Division. Clark reserved the right to change specifications without notice; check against your loader's serial number before ordering parts or setting clearances.

Need the complete Bobcat 700 & 720 service manual?

Get the full 242-page Clark Melroe service manual (6556619) for the 700, 720, 721 and 722 as an instant PDF download: preventive maintenance, loader hydraulics, hydrostatic drive, final drive chains, electrical, Wisconsin, Deutz and Ford engine overhaul, both colour flow chart foldouts, the factory service bulletins and the technical data reproduced above.

Download the Service Manual

Manual code: 6556619

Specifications last reviewed