Bobcat 721 Skid Steer Loader Specifications

Specs Hub › Bobcat 700 Series › 721

Complete specifications for the Bobcat 721 skid steer loader, transcribed from the technical data section of the Clark Melroe factory service manual (6556619). The 721 is the diesel model of the series, powered by an air-cooled two-cylinder Deutz 411D rated at 26 horsepower. It shares the twin hydrostatic drive and 1200 lb. rated operating capacity of the 700, 720 and 722, and adds a self-equalizing disc parking brake and glow-plug starting. A separate Bobcat 721 parts manual is also available.

Operational & Performance

Operational & Performance
Operating Weight 4500 lbs. (2040 kg)
Shipping Weight (less attachments) 4080 lbs. (1850 kg)
Rated Operating Capacity 1200 lbs. (540 kg)
Lift to Maximum Height 2420 lbs. (1100 kg)
Tipping Load 2550 lbs. (1160 kg)
Raise to Maximum Height 4.9 seconds
Lower from Maximum Height 2.8 seconds
Dump Bucket 1.4 seconds
Rollback Bucket 1.4 seconds
Travel Speed, Work Range Infinitely variable, 0 to 4.2 mph (6.6 km/h)1
Travel Speed, Transport Range Infinitely variable, 0 to 6.1 mph (9.8 km/h)

Controls

Controls
Vehicle Steering, direction and speed controlled by two hand levers and a hand grip range selector
Brake Hand brake, disc type, self-equalizing
Loader Lift, tilt and auxiliary functions controlled by separate foot pedals
Engine Hand lever throttle and key-type starter switch
Main Drive Hydrostatic

Engine

Engine
Make / Model Deutz 411D
Type Diesel, air cooled
Fuel No. 2 diesel
Number of Cylinders 2
Bore / Stroke 3.62 in. / 4.13 in. (91.95 mm / 104.90 mm)
Displacement 85.2 cu. in. (1.39 liters)2
Governed Flywheel Horsepower 26 hp (19 kW) @ 2500 rpm
Maximum Torque 57.90 ft.-lbs. (79 N·m) @ 2000 rpm
Firing Order 2-1
High Idle Speed 2675 rpm
Low Idle Speed 950 rpm
Lubrication Pressure
Crankcase Vent Filtered road vent
Air Cleaner Replaceable dry cartridge type with condition indicator
Engine Pre-Heater 12-volt glow plug

Fuel Injection

Fuel Injection
Fuel Lift Pump Pressure 4–5 psi (27.5–34.5 kPa)
Injection Pump Bosch PFR2K70A414/2
Injection Nozzle DLLA 152 S 533
Nozzle Release Pressure, New 2560–2673 psi (17,649–18,428 kPa)
Nozzle Release Pressure, Used 2488–2602 psi (17,152–17,938 kPa)
Injection Timing (start of injection) 25° BTDC
Pump Mounting Flange to Camshaft Base Circle 3.248–3.256 in. (82.5–82.7 mm), including gasket and shims

Engine Oil Viscosity

Choose by the temperature range expected before the next oil change. The manual says to use summer recommendations in winter if the machine is kept in a warm building.3

Engine Oil Viscosity
API Service Class SE for gasoline engines; CD for diesel engines
SAE 10W-30 / 10W-40 −10°F (−23°C) and above
SAE 15W-40 About +5°F (−15°C) and above
SAE 5W-30 Below +60°F (+15°C)
SAE 30 +50°F (+10°C) and above
SAE 20W / 20 +15°F to +70°F (−9°C to +21°C)
SAE 10W Below +40°F (+4°C)

Loader Hydraulics

Loader Hydraulics
Pump Engine driven, vane type
System Relief Pressure 2100 psi (14,479 kPa)4
Cylinders Double-acting
Valves Open-centre type with float detent on lift
Fluid Lines SAE standard full-flow tubes, hoses and fittings
Hydraulic Cylinders
Cylinder Bore Rod Stroke
Lift 2.00 in. (50.80 mm) 1.25 in. (31.75 mm) 25.90 in. (657.86 mm)
Tilt 2.00 in. (50.80 mm) 1.00 in. (25.40 mm) 16.60 in. (419.10 mm)5

Power Train

Power Train
Transmission Two infinitely variable, fully reversing hydrostatic
Reduction Ratio, High Range Infinite to 32.21:1
Reduction Ratio, Low Range Infinite to 46.5:1
Final Drive #80 roller chain running in a sealed oil bath
Brakes Disc type

Electrical

Electrical
Alternator Enclosed, belt driven, 22 amp
Battery 12-volt, 70 amp-hour rating
Starter 12-volt gear drive

Capacities

Capacities
Fuel Tank, Steel 13.5 gal. (51.10 liters)
Fuel Tank, Plastic 16.5 gal. (62.46 liters)
Engine Oil, Including Filter 4 qt. (3.8 liters)
Hydraulic Reservoir 17 gal. (64.35 liters)

Tires & Floor Pressure

Tires & Floor Pressure
Standard Tires 7.00 × 15, 6-ply rating, 50 psi (345 kPa)
Flotation Tires 10.00 × 16.5, 4-ply rating, 35 psi (241 kPa)
Floor Pressure
Floor Pressure, psi (kPa) Front Rear
Standard Tires, Rated Load 49.0 (338) 40.1 (276)
Standard Tires, Unloaded 38.0 (262) 45.1 (311)
Flotation Tires, Rated Load 29.1 (201) 23.4 (161)
Flotation Tires, Unloaded 22.8 (157) 27 (186)

Dimensions

With dirt bucket. Dimensions may vary with other bucket types. Inches with millimetres in parentheses, as printed on the manual's dimension drawing.

Dimensions
Overall Operating Height (bucket fully raised) 138 in. (3505 mm)
Height to Bucket Hinge Pin (fully raised) 109 in. (2769 mm)6
Dump Height 87 in. (2210 mm)
Dump Reach 16.5 in. (419 mm)
Height to Top of Operator Guard 83 in. (2180 mm)7
Length without Bucket 88 in. (2235 mm)
Length with Bucket 111.5 in. (2832 mm)
Wheelbase 35 in. (889 mm)
Width over Bucket 54 in. (1372 mm)
Width over Tires 53.5 in. (1359 mm)
Tread Width (wheel centres) 45.75 in. (1162 mm)
Ground Clearance 8 in. (203 mm)
Turning Clearance Radius, Front (with bucket) 65 in. (1651 mm)
Turning Clearance Radius, Rear 54 in. (1372 mm)
Maximum Dump Angle 36°
Bucket Rollback at Ground 26°
Bucket Rollback in Carry Position 45°
Departure Angle (rear) 26°

Notes:
1 Printed as “0 to 4.2 MPH (6,6 km/hr)”. 4.2 mph is about 6.76 km/h, as printed on the 700/720 page.
2 The loader page gives 85.2 cu. in. (1.4 l); the engine specification page gives 1.39 liters.
3 The viscosity ranges are read from the bar chart on the engine specification page (PI-2358), which is the same for all three engines. The end points are approximate.
4 Printed as “2100 PSI (14,4 kPa)”. 2100 psi is about 14,479 kPa (14.4 MPa), so the unit is a misprint.
5 Printed as 16.6 in. (419.10 mm) for all models. 419.10 mm is exactly 16.5 in.; 16.6 in. would be about 421.6 mm. Both figures are shown as printed.
6 The 721 drawing marks four heights to points on the raised bucket: 138, 121, 109 and 102 in. Printed as “109 (2269)”; 109 in. is 2769 mm, as on the 700/720 and 722 drawings.
7 Printed as “83 (2180)”. 83 in. is about 2108 mm.
All specifications transcribed from the Bobcat 700, 720, 721, 722 Loader Service Manual (6556619), pages 8B-1 and 8B-4, published by Clark Equipment Company, Melroe Division. Clark reserved the right to change specifications without notice; check against your loader's serial number before ordering parts or setting clearances.

Need the complete Bobcat 721 service manual?

Get the full 242-page Clark Melroe service manual (6556619) for the 700, 720, 721 and 722 as an instant PDF download: preventive maintenance, loader hydraulics, hydrostatic drive, final drive chains, electrical, Wisconsin, Deutz and Ford engine overhaul, both colour flow chart foldouts, the factory service bulletins and the technical data reproduced above.

Download the Service Manual

Manual code: 6556619

Specifications last reviewed