Home » Ford 1310 Tractor Specifications

Ford 1310 Tractor Specifications

Specs Hub › Ford › 1310

Complete specifications for the Ford 1310 compact tractor, transcribed from the specifications section of the factory operator's manual (SE4066A). The 1310 sits above the 1210 in Ford's 10-series compact range, with a larger 58.21 cu. in. three-cylinder Shibaura diesel and a twelve-speed transmission. Steering was offered as manual or with hydraulic power assist, and both two-wheel and four-wheel drive figures are given below where they differ.

Jump to Section:

Engine

Type Diesel
Number of Cylinders 3
Bore 2.95 in. (7.5 cm)
Stroke 2.83 in. (7.2 cm)
Displacement 58.21 cu. in. (954 cc)
Compression Ratio 23 : 1
Firing Order 1-2-3
Low Idle Speed 750–850 rpm
Maximum Speed — High Idle 2950–3000 rpm
Maximum Speed — Rated 2800 rpm
Valve Clearance (Cold) — Intake 0.008 in. (0.2 mm)
Valve Clearance (Cold) — Exhaust 0.008 in. (0.2 mm)

Capacities

Component U.S. Imperial Metric
Fuel Tank 7 gals. 5.8 gals. 26.6 liters
Cooling System 2.8 qts. 2.4 qts. 2.7 liters
Engine Crankcase — Less Filter 3.3 qts. 2.7 qts. 3.1 liters
Engine Crankcase — With Filter Change 3.7 qts. 3.0 qts. 3.5 liters
Rear Axle and Transmission (includes hydraulics and optional power steering) 18 qts. 15 qts. 17 liters
Front Axle Differential Case and Final Reduction 3.2 qts. 2.6 qts. 3 liters

Cooling System

Type Pressurized liquid with recirculating bypass
Water Pump — Type Centrifugal
Water Pump — Drive V-belt
Water Pump Belt Deflection 7/16 to 9/16 in. (10–15 mm) when 20–25 lbs. (9–11 kg) thumb force is applied midway between pulleys
Fan Diameter 13.2 in. (33.5 cm)
Thermostat — Starts to Open 160°F (71°C)
Thermostat — Fully Open 185°F (85°C)
Radiator Cap 12.8 psi (0.88 bar)

Electrical System

Alternator 12-volt, heavy duty, 35 amps
Regulator (Alternator) Mechanical
Battery 12-volt, 70 amp. hour rating with negative ground
Starting Motor Solenoid, pre-engaged

Fuel System

Fuel Temperature Type
Diesel Above 20°F (−6.7°C) No. 2D, cetane rating 45
Diesel Below 20°F (−6.7°C) No. 1D, cetane rating 50
Injection Pump — Type In-line
Injection Pump — Timing 20–21° BTDC

Clutch

Type 8.5 in. (21.59 cm) dry disc, organic face
Pedal Free-Travel 3/4–1-3/16 in. (19–30 mm)

Brakes

Type Drum (expanding shoe)
Drum 5.9 in. diameter (15.0 cm)

Steering

Type Manual or hydraulic power assist
Turns Lock-to-Lock 2.3
Steering Wheel Free-Play 0.78–1.38 in. (20–35 mm)
Front Wheel Toe-In 0–13/64 in. (0–5 mm)
Turning Radius (without brake) — Two Wheel Drive 8.4 ft. (255 cm)
Turning Radius (without brake) — Four Wheel Drive 9.1 ft. (276 cm)

Power Take-Off

Type Transmission
Shaft 1-3/8 in. (3.49 cm), 6 spline SAE STD
Engine Speed for 540 rpm PTO Operation 2422 rpm
Horsepower PTO — Observed 16.5

Hydraulic Lift System

Type Live, Category 1 three-point linkage
Pump Capacity1 6.4 U.S. gpm; 7.8 U.S. gpm at 2133 psi at 2800 rpm (5.3 Imp. gpm at 147 bar at 2800 rpm)
System Relief Valve Setting 2133 psi (147 bar)

Cast Iron Weights

(3) Front End Weights 33 lbs. (15 kg) each
(4) Front Wheel Weights (two wheel drive only) 33 lbs. (15 kg) per wheel
(4) Rear Wheel Weights 66 lbs. (30 kg) each

Draw Bars

Fixed Standard
Adjustable Optional

Tires

Position Two Wheel Drive Four Wheel Drive
Front — Standard (AG) 4.00-12, F2, 4 PR 6-12, R1, 4 PR
Front — Optional (Turf) 23-8.50-12, 2 PR 25-8.50-14, 2 PR
Rear — Standard (AG) 8.3 × 24, R1, 4 PR 12.4 × 16, R1, 4 PR2
Rear — Optional (Turf) 13.6-16, R3, 4 PR — (two wheel drive only)

Wheel Bolt Torques

Fastener Two Wheel Drive Four Wheel Drive
Front Wheel Disc-to-Hub 43–54 lb. ft. (58–73 N·m) 68.6–86.7 lb. ft. (93–117 N·m)
Rear Wheel Disc-to-Rim 137–159 lbs. ft. (186–215 N·m)

Lubricants

Tractor Component Ford Specification Number Ford Part No.
Engine Oil Ford 121 (meets M2C-121-B API grade CD and MIL-L-2104C) 1QM-2C 121-AMV (case, 24 qts. 15W-40); 1QM-2C 121-A10 (case, 24 qts. SAE 10W); 1QM-2C 121-A30 (case, 24 qts. SAE 30W)
Transmission, Rear Axle, Power Steering and Hydraulic System Oil Ford 134 1GM-134B (1 gal.); 5GM-134B (5 gal.)
Front Wheel Bearings and Lubrication Fittings M1C-137-A 1TM-1C-137-A (1 tube)
Front Axles Ford 134 1GM-134B (1 gal.); EOAZ-19580-E (5 gal.)

The manual notes that if the recommended engine oil is not readily available, a commercial oil may be used, selected by outdoor temperature from a chart giving SAE 10W, 10W30, 15W40 and 30 grades across a range anchored at −13°F (−25°C), 14°F (−10°C), 32°F (0°C) and 90°F (32°C).3 It also notes that engine crankcase oil drain intervals should be shortened when diesel fuel sulfur content is above 0.5%.4

General Dimensions

Dimension Two Wheel Drive Four Wheel Drive
Length 109.3 in. (277.5 cm) 109.3 in. (277.5 cm)
Wheelbase 63 in. (160 cm) 63 in. (160 cm)
Height — Top of Steering Wheel 56.5 in. (143.5 cm) 55.1 in. (140 cm)
Height — Top of ROPS —5 —5
Height — Top of Vertical Exhaust 71 in. (180.3 cm) 69.1 in. (175.5 cm)
Width 49.6 in. (126.0 cm) 55.7 in. (141.5 cm)
Minimum Ground Clearance 13 in. (33 cm) 10.6 in. (27 cm)
Adjustable Width — Front 40.4–51 in. (102.5–129.5 cm) 45.7 in. (116 cm)
Adjustable Width — Rear 41.2–52 in. (104.6–132 cm) 43.3–45.5 in.
Weight (less options) 1819 lbs. (825 kg) 2103 lbs. (954 kg)

Ground Speeds

From 1400–2800 rpm engine speed, with 8.3 × 24 rear tires.6

Gear Position At 1400 rpm (mph) At 2800 rpm (mph)
Forward
1st 0.4 0.7
2nd 0.5 0.9
3rd 0.6 1.2
4th 0.8 1.6
5th 1.0 2.1
6th 1.3 2.7
7th 1.8 3.6
8th 2.3 4.6
9th 2.9 5.9
10th 3.6 7.2
11th 4.6 9.2
12th 5.9 11.9
Reverse
R1 0.4 0.8
R2 0.9 1.9
R3 2.0 4.1
R4 4.1 8.3

Notes:
1 The manual prints two consecutive “Pump Capacity” lines — 6.4 U.S. gpm and 7.8 U.S. gpm — with a single Imperial figure of 5.3 gpm, which corresponds to the 6.4 U.S. gpm value. Both U.S. figures are reproduced as printed; the source does not label which configuration each applies to.
2 The manual gives a different rear tire size for four-wheel drive (12.4 × 16) than for two-wheel drive (8.3 × 24), on a smaller rim. Reproduced as printed.
3 The manual gives the oil viscosity recommendation as a graphical chart of overlapping temperature bands rather than a table. The anchor temperatures are reproduced above; see the operator's manual for the chart itself.
4 The manual prints “disesl” in this note; spelling normalised.
5 The manual lists a “Top of ROPS” row in the dimensions table but leaves both values blank.
6 The manual presents ground speeds as a bar chart rather than a table. The values above are the endpoint figures printed on that chart at 1400 and 2800 rpm — they are transcribed, not measured from the graph.
All specifications transcribed from the specifications section of the Ford 1310 operator's manual, manual code SE4066A, originally published by Ford Tractor Operations, Ford Motor Company. Ford reserved the right to change specifications without notice; verify against your tractor's serial number before ordering parts or setting clearances.

Need the complete Ford 1310 operator's manual?

Get the full 60-page manual as an instant PDF download — controls and instruments, operating procedures, 2WD and 4WD service schedules, and the specification section reproduced above.

Download the Operators Manual

Other Ford 10-series compact tractors covered on this site:

Browse All Ford Tractor Manuals

All Ford specifications

Manual code: SE4066A

Specifications last reviewed