New Holland Hayliner 273 Baler Specifications

Specs Hub › New Holland › Hayliner 273

About this model: New Holland’s Hayliner 273 is a late-’60s/’70s-era 14×18-inch small square baler known for a dependable two-knotter twine system (wire optional), smooth 540-PTO drive, and clean pickup (many with SuperSweep), a comfortable match for roughly 35–60 HP tractors.

General

Over-All Width
(Standard tires)	8' 4⅝"
(Flotation tires)	8' 8⅝"
Over-All Height
(P.T.O.)	4' 2⅞"
(Engine)	6' 7⅛"
Over-All Length — Short Tongue
Chute Up	14' 11"
Chute Down	17' 7"
Over-All Length — Long Tongue
Chute Up	16' 8"
Chute Down	19' 5"
Weight
Short Tongue (P.T.O.) — Twine	2577 lb
Short Tongue (P.T.O.) — Wire	2639 lb
Long Tongue (P.T.O.) — Twine	2675 lb
Long Tongue (P.T.O.) — Wire	2737 lb
Long Tongue (Engine) — Twine (Super-Sweep)	2915 lb
Long Tongue (Engine) — Wire (Super-Sweep)	2977 lb
Wheel Tread	7' 11-7/16"
Wheel Bearings	Tapered Roller
Maximum Road Speed	20 M.P.H.

P.T.O.

Type — Short Tongue	2-Joint — ASAE Standard
Type — Long Tongue	3-Joint — ASAE Standard
Protection	Friction Clutch plus Overrunning Clutch

Engine

Make	Wisconsin THD — Air Cooled
Speed	70 strokes/minute
Rated	2820 RPM — 17.5 HP
Fuel Tank Capacity	9.4 gal

Tires

Pick-Up
Size	3.00 × 12 — Semi-Pneumatic
Right Wheel
(Standard)	5.00 × 15, 4-ply — 28 psi
Flotation	25 × 7.50 × 15, 4-ply — 30 psi
Left Wheel
(Standard)	6.40 × 15, 6-ply — 44 psi
Flotation	27 × 9.50 × 15, 6-ply — 35 psi

Pick-Up

Width (incl. 5½" flare)	61½"
Drive	Roller Chain
Protection	Friction Clutch and Overrunning Clutch
Shaft Bearings	Sealed Ball

Feature	Standard	SuperSweep
Number of Tooth Bars	4	6
Tooth Bar Bearings	Self-Lubricating	Sealed Ball
Number of Teeth	48	120
Windguard	11 Finger	9 Finger
Tooth Spacing	4⅜"	2⅝"

Feeding System

Drive	Telescoping Linkage to Plunger
Protection	Spring Loaded
Tines	6 Spring-Loaded Aluminum Fingers
Feed Opening	266 sq. in.
Bearings	Sealed Ball and Tapered Roller

Bale Chamber

Size	14" × 18"
Bale Length	12" to 52"

Knotter

Protection	Shear Bolt
Tying	Twine

Twister

Protection	Shear Bolt
Twisting	14½-ga. Wire

Plunger

Speed	66 strokes per minute @ 540 r.p.m. (range: 65–75 SPM)
Stroke	30"
Needle Latch	Contacts Crank Arm
Rollers — Twine Model	7 sealed ball bearings (5 vertical, 2 horizontal)
Rollers — Wire Model	8 sealed ball bearings (6 vertical, 2 horizontal)
Crank Pin	Sealed Ball Bearing
Plunger Pin	Sleeve Bearing with Seals

Main Drive

Flywheel Diameter	22"
Protection	Shear Bolt
Bearings	Tapered Roller
Gearbox	Alloy steel gears running in oil
Gearbox Ratio	Output/Input — 6/49

Need the official New Holland 273 owner’s manual?
Download the PDF here →