Home » Ford 1110 Tractor Specifications

Ford 1110 Tractor Specifications

Specs Hub › Ford › 1110

Complete specifications for the Ford 1110 compact tractor, transcribed from the specifications section of the factory operator's manual (SE 4064). Built from 1983 to 1986 by Shibaura in Japan as the smallest model in Ford's Ten Compact Series, the 1110 has a 43.1 cu. in. two-cylinder diesel and 11.5 observed PTO horsepower. It was sold with a 10-speed gear transmission or a two-range hydrostatic drive, in two-wheel or four-wheel drive, and the figures below separate the versions where the manual does.

Jump to Section:

Engine

Type Diesel
Number of Cylinders 2
Bore 2.95 in. (7.5 cm)
Stroke 3.15 in. (8.0 cm)
Displacement 43.1 cu. in. (706 cc)
Compression Ratio 23 : 1
Firing Order 2-1
Low Idle Speed 750–850 rpm
Maximum Speed — High Idle 2750–2800 rpm
Maximum Speed — Rated 2600 rpm
Valve Clearance (Cold) — Intake 0.012 in. (0.30 mm)
Valve Clearance (Cold) — Exhaust 0.012 in. (0.30 mm)

Capacities

Component U.S. Imperial Metric
Fuel Tank 4.8 gals. 4.0 gals. 18 liters
Cooling System 3.4 qts. 2.8 qts. 3.2 liters
Engine Crankcase — Less Filter 2.3 qts. 1.9 qts. 2.2 liters
Engine Crankcase — With Filter Change 2.6 qts. 2.2 qts. 2.5 liters
Rear Axle and Transmission (includes hydraulics) 17 qts. 14.2 qts. 16.1 liters
Rear Axle and H.S.T. (includes hydraulics) 15.3 qts. 12.8 qts. 14.5 liters
Front Axle Final Reduction and Differential Gear Case 1.62 qts. 1.36 qts. 1.5 liters

Cooling System

Type Pressurized liquid with recirculating bypass
Water Pump — Type Centrifugal
Water Pump — Drive V-belt
Water Pump Belt Deflection 7/16 to 9/16 (10–15 mm) when 20–25 lbs. (9–11 kg) thumb force is applied midway between pulleys1
Fan Diameter 11.81 in. (30.0 cm)
Thermostat — Start to Open 160°F (71°C)
Thermostat — Fully Open 185°F (85°C)
Radiator Cap 13 psi (0.88 bar)

Electrical System

Alternator 12-volt, heavy duty, 35 amps
Regulator (Alternator) Mechanical
Battery 12-volt, 65 amp. hour rating with negative ground
Starting Motor Solenoid, pre-engaged

Fuel System

Fuel Temperature Type
Diesel Above 20°F (−6.7°C) No. 2D, cetane rating 45
Diesel Below 20°F (−6.7°C) No. 1D, cetane rating 50
Injection Pump — Type In-line
Injection Pump — Timing 24° BTDC

Clutch

Type 6.3 in. (16.0 cm) dry disc, organic face
Pedal Free-Travel 3/4–1-3/16 in. (19–30 mm)

Brakes

Type Drum (expanding shoe)
Drum Diameter 4.33 in. (11.0 cm)

Steering

Type Manual
Turns Lock-to-Lock 2.32
Steering Wheel Free-Play 0.78–1.38 in. (20–35 mm)
Front Wheel Toe-In 0–13/64 in. (0–5 mm)
Turning Radius (without brake) — Two Wheel Drive 7.2 ft. (219 cm)
Turning Radius (without brake) — Four Wheel Drive 8.0 ft. (244 cm)

Power Take-Off

Type Transmission
Shaft 1-3/8 in. (3.49 cm), 6 spline SAE STD
Engine Speed for 540 rpm PTO — Gear Transmission 2568 rpm
Engine Speed for 540 rpm PTO — Hydrostatic Transmission 2575 rpm
Horsepower PTO — Observed 11.5

Hydraulic Lift System

Type Live, Category 1 three-point linkage3
Pump Type Gear
Pump Capacity 4.1 gpm at 1849 psi at 2600 rpm (3.4 Imp. gpm at 127 bar at 2600 rpm)4
System Relief Valve Setting 1849 psi (127 bar)

Tires

Position Two Wheel Drive Four Wheel Drive
Front — Standard (AG) 4.00-12, F2, 4 PR 5-12, G1, 4 PR
Front — Optional (Turf) 2.00 × 8.00-10, G2, 2 PR — Two & Four Wheel Drive5
Rear — Standard (AG) 8-16, R1, 4 PR — Two & Four Wheel Drive
Rear — Optional (Turf) 29 × 12.00-15, R3, 4 PR — Two & Four Wheel Drive

Wheel Bolt Torques

Front Wheel — Disc-to-Hub 43–54 lbs. ft. (58–73 N·m)
Rear Wheel — Disc-to-Axle 69–87 lbs. ft. (93–117 N·m)6
Front Axle — Side Axle Adjusting Bolts 137–159 lbs. ft. (186–215 N·m)7
Front Axle — Tie Rod Setting Bolts 31–41 lbs. ft. (42–55 N·m)7

Cast Iron Weights

(3) Front End Weights 33 lbs. (15 kg) each
(4) Rear Wheel Weights 66 lbs. (20 kg) each8

Draw Bars

Fixed Standard

Lubricants

Tractor Component Ford Specification Number Ford Part No.
Engine Oil M2C-121-A (meets M2C-121-B, API grade CD and MIL-L-2104C) 1QM-2C 121-AMV (case, 24 qts. 15W-40); 1QM-2C 121-A10 (case, 24 qts. SAE 10W); 1QM-2C 121-A30 (case, 24 qts. SAE 30W)
Transmission, Rear Axle and Hydraulic System Oil (mechanical transmission) M2C-134-B 1 QM-134B (1 gal.); 5GM-134B (5 gal.)9
Transmission, Rear Axle and Hydraulic System Oil (hydrostatic transmission) M2C-41-A None printed
Lubrication Fittings M1C-137-A 1TM-1C-137-A (1 tube)
Front Axles M2C-105-A E0AZ-19580-B (1 gal.); E0AZ-19580-E (5 gal.)
Temperature Viscosity Grade and API Class
Year around SAE 10W30, 10W40 (CD)
Below 32°F (0°C) SAE 10W (CD or CC/CD)
32 to 50°F (0–10°C) SAE 20W (CD or CC/CD)
Above 50°F (10°C) SAE 30W (CD or CC/CD)

The manual notes that if the recommended engine oil is not readily available, a commercial oil may be used as shown in the chart above.

General Dimensions

Dimension Two Wheel Drive Four Wheel Drive
Length 101.3 in. (257 cm) — Two & Four Wheel Drive
Wheelbase 55.1 in. (140 cm) — Two & Four Wheel Drive
Height — Top of Steering Wheel 50.4 in. (128 cm) — Two & Four Wheel Drive
Height — Top of ROPS Not printed10
Width 44.1 in. (112 cm) — Two & Four Wheel Drive
Minimum Ground Clearance 9.7 in. (24.6 cm) — Two & Four Wheel Drive
Adjustable Width — Front 33.9–57.5 in. (86–92 cm)11 34.6 in. (88 cm)
Adjustable Width — Rear 35.4–41.3 in. (90–105 cm) — Two & Four Wheel Drive
Weight (Less Options) — Gear Transmission 1235 lbs. (560 kg) 1322 lbs. (600 kg)
Weight (Less Options) — H.S.T. 1300 lbs. (540 kg)12 1385 lbs. (630 kg)

Ground Speeds

From 1300 to 2600 rpm engine speed with 8 × 16 rear tires.13

Gear Position At 1300 rpm (mph) At 2600 rpm (mph)
Forward — Gear Transmission
1st 0.3 0.7
2nd 0.4 0.9
3rd 0.6 1.2
4th 0.8 1.6
5th 1.0 2.1
6th 1.5 3.0
7th 2.0 4.0
8th 2.7 5.4
9th 3.6 7.2
10th 4.7 9.5
Reverse — Gear Transmission
R1 0.6 1.2
R2 2.6 5.2
HST Low Range — Forward / Reverse 0–3.5 mph / 0–2.3 mph
HST High Range — Forward / Reverse 0–9.3 mph / 0–6.0 mph

Notes:
1 The belt deflection is printed as “7/16 to 9/16 (10-15 mm)” with no unit on the first figure. 10–15 mm is about 0.39–0.59 in., consistent with inches. Transcribed as printed.
2 Printed as “−2.3” with a leading dash, which reads as a print artifact. Shown as 2.3.
3 Printed as “Live Catefory 1”, a typesetting error for Category 1.
4 The pump capacity is printed in U.S. and Imperial gallons only, with no liters-per-minute figure. 1849 psi is about 127.5 bar, consistent with the 127 bar printed.
5 Printed as “2.00 x 8.00-10, G2. 2PR”. A turf tire this small would more usually be written 20 × 8.00-10, but the figure is transcribed as printed.
6 On the printed page a “Front Wheel” label sits on its own line above “Rear Wheel Disc-to-Axle … 69-87 lbs. ft. (93-117 N.m)” with no value of its own. The 69–87 lbs. ft. figure is shown against the rear wheel.
7 The side axle adjusting bolt and tie rod setting bolt torques are from the wheel tread settings section (page 20), not the specifications pages.
8 66 lbs. is about 30 kg, not 20 kg. Both figures are transcribed as printed.
9 Printed as “1 QM-134B”. The 5-gallon part is 5GM-134B, so the 1-gallon part is most likely 1GM-134B, but the manual's text is shown. No part number is printed for the M2C-41-A hydrostatic transmission oil.
10 The dimensions table has a “Top of ROPS” line with no figure against it.
11 Printed as “33.9-57.5 in. (86-92 cm)”. 86–92 cm is 33.9–36.2 in., and the wheel tread section (page 20) gives 33.9 to 36.2 in. for the standard front axle, so 57.5 is a misprint for 36.2. That section also gives 30.3 to 40.9 in. (77–104 cm) with the optional adjustable front axle, and 35.4 to 46 in. (90–116.8 cm) at the rear with the optional adjustable rear wheels.
12 1300 lbs. is about 590 kg, not 540 kg. The H.S.T. figures are printed as superscripts beside the gear transmission weights. Both are transcribed as printed.
13 The manual presents ground speeds as a bar chart rather than a table. The values above are the endpoint figures printed on that chart, transcribed rather than measured from the graph. The hydrostatic figures are the maximum lines marked “H.S.T” on the same chart, and they agree with the H.S.T. range selector description on page 11. A creeper range accessory (5.5:1) adds 5 forward and 1 reverse speeds to the gear transmission; the manual gives no speeds for it.
All specifications transcribed from the Ford 1110 operator's manual, publication SE 4064, originally published by Ford Tractor Operations. Production years, builder, series and engine model are from TractorData and are not printed in the manual. Ford reserved the right to change specifications without notice; verify against your tractor's serial number before ordering parts or setting clearances.

Need the complete Ford 1110 operator's manual?

Get the full 64-page manual as an instant PDF download: 10-speed gear and hydrostatic transmission controls, operating procedures, tread settings and weighting, separate 2WD and 4WD service schedules, and the specification section reproduced above.

Download the Operators Manual

Other Ford compact tractors covered on this site:

For how the 1110 compares with every other Ford compact, see Ford Compact Tractors: Every Model Compared.

Browse All Ford Tractor Manuals

All Ford specifications

Manual code: SE 4064

Specifications last reviewed