Home » Ford 2110 Tractor Specifications

Ford 2110 Tractor Specifications

Specs Hub › Ford › 2110

Complete specifications for the Ford 2110 compact utility tractor, transcribed from the specifications section of the factory operator's manual (SE 4312). Built from 1983 to 1987 by Shibaura in Japan and sold as part of Ford's Ten Compact Series, the 2110 uses a four-cylinder diesel of 138.5 cu. in. and sits at the top of that range. Both two-wheel and four-wheel drive figures are given below, along with ground speeds for the twelve-speed transmission.

Jump to Section:

Engine

Type Diesel
Number of Cylinders 4
Bore 3.35 in. (8.5 cm)
Stroke 3.94 in. (10.0 cm)
Displacement 138.5 cu. in. (2269 cc)
Compression Ratio 21 : 1
Firing Order 1-3-4-2
Low Idle Speed 700–800 rpm
Maximum Speed — High Idle 2650–2700 rpm
Maximum Speed — Rated 2500 rpm
Valve Clearance (Cold) — Intake 0.012 in. (0.3 mm)
Valve Clearance (Cold) — Exhaust 0.012 in. (0.3 mm)

Capacities

Component U.S. Imperial Metric
Fuel Tank 10.6 gals. 8.8 gals. 40 liters
Cooling System 9.1 qts. 7.5 qts. 8.5 liters
Engine Crankcase — Less Filter 7.5 qts. 6.2 qts. 7.1 liters
Engine Crankcase — With Filter Change 8.0 qts. 6.6 qts. 7.5 liters
Rear Axle and Transmission (includes hydraulics and optional power steering) 34.3 qts. 28.3 qts. 32.2 liters
Front Axle Differential Case and Final Reduction 8.0 qts. 6.6 qts. 7.5 liters

Cooling System

Type Pressurized liquid with recirculating bypass
Water Pump — Type Centrifugal
Water Pump — Drive V-belt
Water Pump Belt Deflection 7/16 to 9/16 in. (10–15 mm) when 20–25 lbs. (9–11 kg) thumb force is applied midway between pulleys
Fan Diameter 16.1 in. (41 cm)
Thermostat — Starts to Open 160°F (71°C)
Thermostat — Fully Open 185°F (85°C)
Radiator Cap 12.8 psi (0.88 bar)

Electrical System

Alternator 12-volt, heavy duty, 35 amps
Regulator (Alternator) Mechanical
Battery 12-volt, 100 amp. hour rating with negative ground
Starting Motor Solenoid, pre-engaged

Fuel System

Fuel Temperature Type
Diesel Above 20°F (−6.7°C) No. 2D, cetane rating min. 40
Diesel Below 20°F (−6.7°C) No. 1D, cetane rating min. 40
Injection Pump — Type In-line
Injection Pump — Timing 24° BTDC

Clutch

Type 9.45 in. (24.0 cm) dry disc, organic face
Pedal Free-Travel 3/4–1-3/16 in. (19–30 mm)

Brakes

Type Drum (expanding shoe)
Drum 7.87 in. diameter (20.0 cm)

Steering

Type Manual or hydraulic power assist
Turns Lock-to-Lock 2.3
Steering Wheel Free-Play 0.78–1.38 in. (20–35 mm)
Front Wheel Toe-In 0–13/64 in. (0–5 mm)
Turning Radius (without brake) — Two Wheel Drive 10.4 ft. (317.5 cm)
Turning Radius (without brake) — Four Wheel Drive 11.8 ft. (360 cm)

Power Take-Off

Type Live P.T.O., transmission
Shaft 1-3/8 in. (3.49 cm), 6 spline SAE STD
Engine Speed for 540 rpm PTO Operation 2392 rpm
Horsepower PTO — Observed 34.5

Hydraulic Lift System

Type Live, Category 1 three-point linkage
Pump Type Gear
Pump Capacity 8.6 U.S. gpm at 2133 psi at 2500 rpm (7.2 Imp. gpm at 147 bar at 2500 rpm)
System Relief Valve Setting 2133 psi (147 bar)

Tires

Position Two Wheel Drive Four Wheel Drive
Front — Standard (AG) 6.00-16, F2, 4PR 8-18, R1, 4PR
Front — Optional (Turf) 25-8.50-14, 2PR 27-8.50-15, 2PR
Rear — Standard (AG) 13.6 × 28, R1, 4PR — Two & Four Wheel Drive
Rear — Optional (Turf) 18.4 × 16.1, R3, 4PR Not offered

Wheel & ROPS Bolt Torques

Fastener Two Wheel Drive Four Wheel Drive
Front Wheel Disc-to-Hub 69–87 lbs. ft. (93–117 N·m) 137–159 lbs. ft. (185–215 N·m)
Rear Wheel Disc-to-Rim1 137–159 lbs. ft. (185–215 N·m)
Rear Wheel Disc-to-Axle1 137–159 lbs. ft. (185–215 N·m)
ROPS to Trumpet Housing (M12) 80 lbs. ft. (108 N·m)
ROPS to Lower Mount (M20) 110 lbs. ft. (152 N·m)
ROPS Crossmember Attachment (M12)2 60 lbs. ft. (108 N·m)
Seat Belt (M12) 80 lbs. ft. (108 N·m)

Cast Iron Weights

(3) Front End Weights 33 lbs. (15 kg) each
(4) Front Wheel Weights (two wheel drive only) 33 lbs. (15 kg) per wheel
(4) Rear Wheel Weights 66 lbs. (30 kg) each

Draw Bars

Swing Draw Bar Standard

Lubricants

Tractor Component Ford Specification Number Ford Part No.
Engine Oil Ford 121 (meets M2C-121-B, API grade CD and MIL-L-2104C) 1QM-2C 121-AMV (case, 24 qts. 15W-40); 1QM-2C 121-A10 (case, 24 qts. SAE 10W); 1QM-2C 121-A30 (case, 24 qts. SAE 30W)
Transmission, Rear Axle, Power Steering and Hydraulic System Oil Ford 134 1GM-134B (1 gal.); 5GM-134B (5 gal.)
Front Wheel Bearings and Lubrication Fittings M1C-137-A3 1TM-1C-137-A (1 tube)
Front Axles Ford 134 1GM-134B (1 gal.); EOAZ-19580-E (5 gal.)
SAE 10W4 −13°F to 32°F (−25°C to 0°C)
SAE 10W304 −13°F to 90°F (−25°C to 32°C)
SAE 15W404 14°F (−10°C) and above
SAE 304 32°F (0°C) and above

The manual notes that if the recommended engine oil is not readily available, a commercial oil may be used as shown on its oil chart, and that engine crankcase oil drain intervals should be adjusted downward when diesel fuel sulfur content is above 0.5%.

General Dimensions

Dimension Two Wheel Drive Four Wheel Drive
Length 131 in. (333 cm) 131 in. (333 cm)
Wheelbase 73.2 in. (186 cm) 75.6 in. (192 cm)
Height — Top of Steering Wheel 64 in. (164 cm) 62.8 in. (159.5 cm)
Height — Top of ROPS 90.95 in. (231.0 cm) 90.95 in. (231.0 cm)
Height — Top of Vertical Exhaust 79.7 in. (202.5 cm) 79.3 in. (201.5 cm)
Width 61.7–85.7 in. (156.7–217.7 cm) 61.7–85.7 in. (156.7–217.7 cm)
Minimum Ground Clearance 14.9 in. (38 cm) 14.6 in. (37 cm)
Adjustable Wheel Tread — Front 48–72 in. (122–183 cm) 49.6 in. (126 cm)
Adjustable Wheel Tread — Rear 48–72 in. (122–183 cm) 48–72 in. (122–183 cm)
Weight with ROPS, less options 3538 lbs. (1605 kg) 3758 lbs. (1705 kg)

Ground Speeds

From 1250–2500 rpm engine speed, with 13.6 × 28 rear tires.5

Gear Position At 1250 rpm (mph) At 2500 rpm (mph)
Forward
1st 0.5 1.0
2nd 0.7 1.3
3rd 0.8 1.6
4th 1.2 2.3
5th 1.5 3.0
6th 1.8 3.6
7th 2.5 5.0
8th 3.2 6.4
9th 3.9 7.8
10th 5.4 10.8
11th 6.9 13.7
12th 8.2 16.5
Reverse
R1 0.7 1.4
R2 1.6 3.1
R3 3.4 6.9
R4 7.3 14.7

Notes:
1 The manual prints the rear wheel torque as two labels, “Disc-to-Rim” carrying “137-159 lbs. ft.” and “Disc-to-Axle” carrying “(185-215 N.m)” on the line below. Since 137–159 lbs. ft. converts to 186–216 N·m, this is one specification split across two label lines by the page layout rather than two different values. Both rows are shown with the full figure. Verify against a clean copy before relying on it.
2 The manual prints the ROPS crossmember attachment (M12) torque as “60 lbs. ft. (108 N.m)”. 60 lbs. ft. converts to about 81 N·m, and 108 N·m is the metric value printed for the 80 lbs. ft. fasteners elsewhere in the same table, so one of the two figures is a misprint. Transcribed exactly as printed. Verify against a clean copy.
3 The front wheel bearing grease specification is printed as “IT M1C-137-A”; the leading “IT” appears to be a printing or scanning artifact, and the specification is M1C-137-A.
4 The oil viscosity recommendation is printed as a graphical bar chart against a temperature scale rather than as a table. The ranges above are read from that chart.
5 The manual presents ground speeds as bar charts rather than tables. The values above are the endpoint figures printed on those charts at 1250 and 2500 rpm — they are transcribed, not measured from the graphs.
All specifications transcribed from the specifications section of the Ford 2110 operator's manual, manual code SE 4312, originally published by Ford. Production years, builder and series are from TractorData and are not printed in the manual. Ford reserved the right to change specifications without notice; verify against your tractor's serial number before ordering parts or setting clearances.

Need the complete Ford 2110 operator's manual?

Get the full 68-page manual as an instant PDF download — controls and instruments, operating procedures, tread settings and weighting, separate 2WD and 4WD service schedules, and the specification section reproduced above.

Download the Operators Manual

Other Ford compact tractors covered on this site:

Doing teardown work? The Ford 1910 & 2110 service repair manual covers overhaul procedures, clearances and torque values.

Browse All Ford Tractor Manuals

All Ford specifications

Manual code: SE 4312

Specifications last reviewed