Home » Ford 1910 Tractor Specifications

Ford 1910 Tractor Specifications

Specs Hub › Ford › 1910

Complete specifications for the Ford 1910 compact utility tractor, transcribed from the specifications section of the factory operator's manual (SE 4096B). Built from 1983 to 1986 by Shibaura in Japan as part of Ford's Ten Compact Series, the 1910 uses a three-cylinder diesel of 103.88 cu. in. and sits one step below the four-cylinder 2110. Both two-wheel and four-wheel drive figures are given below, along with ground speeds for the twelve-speed transmission.

Jump to Section:

Engine

Type Diesel
Number of Cylinders 3
Bore 3.35 in. (8.5 cm)
Stroke 3.94 in. (10 cm)
Displacement 103.88 cu. in. (1702 cc)
Compression Ratio 21 : 1
Firing Order 1-2-3
Low Idle Speed 700–800 rpm
Maximum Speed — High Idle 2650–2700 rpm
Maximum Speed — Rated 2500 rpm
Valve Clearance (Cold) — Intake 0.012 in. (0.3 mm)
Valve Clearance (Cold) — Exhaust 0.012 in. (0.3 mm)

Capacities

Component U.S. Imperial Metric
Fuel Tank 9.3 gals. 7.7 gals. 35 liters
Cooling System 7.4 qts. 6.2 qts. 7 liters
Engine Crankcase — Less Filter 6.3 qts. 5.3 qts. 6 liters
Engine Crankcase — With Filter Change 6.9 qts. 5.7 qts. 6.5 liters
Rear Axle and Transmission (includes hydraulics and optional power steering) 29.6 qts. 24.6 qts. 28 liters
Front Axle Differential Case and Final Reduction 5.3 qts. 4.4 qts. 5 liters

Cooling System

Type Pressurized liquid with recirculating bypass
Water Pump — Type Centrifugal
Water Pump — Drive V-belt
Water Pump Belt Deflection 7/16 to 9/16 in. (10–15 mm) when 20–25 lbs. (9–11 kg) thumb force is applied midway between pulleys
Fan Diameter 16.1 in. (41 cm)
Thermostat — Starts to Open 160°F (71°C)
Thermostat — Fully Open 185°F (85°C)
Radiator Cap 12.8 psi (0.88 bar)

Electrical System

Alternator 12-volt, heavy duty, 35 amps
Regulator (Alternator) Mechanical
Battery 12-volt, 100 amp. hour rating with negative ground
Starting Motor Solenoid, pre-engaged

Fuel System

Fuel Temperature Type
Diesel Above 20°F (−6.7°C) No. 2D, cetane rating min. 40
Diesel Below 20°F (−6.7°C) No. 1D, cetane rating min. 40
Injection Pump — Type In-line
Injection Pump — Timing 24° BTDC

Clutch

Type 9.4 in. (24.0 cm) dry disc, organic face
Pedal Free-Travel 3/4–1-3/16 in. (19–30 mm)

Brakes

Type Drum (expanding shoe)
Drum 6.7 in. diameter (17.0 cm)

Steering

Type Manual or hydraulic power assist
Turns Lock-to-Lock 2.3
Steering Wheel Free-Play 0.78–1.38 in. (20–35 mm)
Front Wheel Toe-In 0–13/64 in. (0–5 mm)
Turning Radius (without brake) — Two Wheel Drive 8.7 ft. (265 cm)
Turning Radius (without brake) — Four Wheel Drive 8.7 ft. (265 cm)

Power Take-Off

Type Transmission
Shaft 1-3/8 in. (3.49 cm), 6 spline SAE STD
Engine Speed for 540 rpm PTO Operation 2455 rpm
Horsepower PTO — Observed 28.5

Hydraulic Lift System

Type Live, Category 1 three-point linkage
Pump Type Gear
Pump Capacity — to Hydraulic Lift 7.3 U.S. gpm at 2133 psi at 2500 rpm (6.5 Imp. gpm at 147 bar at 2500 rpm)1
Pump Capacity — for Power Steering 1.3 U.S. gpm at 2133 psi at 2500 rpm
System Relief Valve Setting 2133 psi (147 bar)

Tires

Position Two Wheel Drive Four Wheel Drive
Front — Standard (AG) 5.50-16, F2, 4PR 6.00-16, R1, 4PR
Front — Optional (Turf) 25-8.50-14, 4PR 27-8.50-15, 4PR
Rear — Standard (AG) 13.6 × 24, R1, 4PR — Two & Four Wheel Drive
Rear — Optional (Turf) 18.4 × 16.1, R3, 4PR — Two & Four Wheel Drive

Wheel & ROPS Bolt Torques

Fastener Two Wheel Drive Four Wheel Drive
Front Wheel Disc-to-Hub 69–87 lbs. ft. (93–117 N·m) 137–159 lbs. ft. (186–215 N·m)
Rear Wheel Disc-to-Rim 137–159 lbs. ft. (186–215 N·m)
Rear Wheel Disc-to-Axle 137–159 lbs. ft. (186–215 N·m)
ROPS to Trumpet Housing (M12) 80 lbs. ft. (108 N·m)
ROPS to Lower Mount (M20) 110 lbs. ft. (152 N·m)
ROPS Crossmember Attachment 60 lbs. ft. (81 N·m)
Seat Belt (M12) 80 lbs. ft. (108 N·m)

Cast Iron Weights

(3) Front End Weights 33 lbs. (15 kg) each
(4) Front Wheel Weights (two wheel drive only) 33 lbs. (15 kg) per wheel
(4) Rear Wheel Weights 66 lbs. (30 kg) each

Draw Bars

Swing Draw Bar Standard

Lubricants

Tractor Component Lubricant Recommendation Ford Part No.
Engine Oil Ford Super Premium 1QM-2C 121-AMV (case, 24 qts. 15W-40); 1QM-2C 121-A10 (case, 24 qts. SAE 10W); 1QM-2C 121-A30 (case, 24 qts. SAE 30W)
Transmission, Rear Axle, Power Steering and Hydraulic System Oil Ford 134 1GM-134C (1 gal.); 5GM-134C (5 gal.)
Front Wheel Bearings and Lubrication Fittings M1C-137-B2 1TM-1C-137-B (1 tube)
Front Axles Ford 134 1GM-134C (1 gal.); EOAZ-19580-E (5 gal.)

The manual notes that if the recommended engine oil is not readily available, a commercial oil may be used as shown on its oil chart,3 and that engine crankcase oil drain intervals should be adjusted downward when diesel fuel sulfur content is above 0.5%.

General Dimensions

Dimension Two Wheel Drive Four Wheel Drive
Length 122.6 in. (311.5 cm) 122.6 in. (311.5 cm)
Wheelbase 66.3 in. (168.5 cm) 66.9 in. (170 cm)
Height — Top of Steering Wheel 61.1 in. (156.5 cm)4 60.4 in. (153.5 cm)
Height — Top of ROPS 88.5 in. (224.8 cm) 88.5 in. (224.8 cm)
Height — Top of Vertical Exhaust 77.4 in. (196.5 cm) 76.8 in. (195.0 cm)
Width 63.1 in. (160.2 cm) 63.1 in. (160.2 cm)
Minimum Ground Clearance 13.8 in. (35.0 cm) 13.1 in. (33.3 cm)
Adjustable Width — Front 43.5–57.5 in. (110.5–146 cm) 45.2 in. (115 cm)
Adjustable Width — Rear 45.7–61 in. (116–155 cm) 45.7–61 in. (116–155 cm)
Weight with ROPS 2800 lbs. (1270 kg) 3064 lbs. (1390 kg)

Ground Speeds

From 1250–2500 rpm engine speed, with 13.6 × 24 rear tires.5

Gear Position At 1250 rpm (mph) At 2500 rpm (mph)
Forward
1st 0.4 0.7
2nd 0.5 1.0
3rd 0.6 1.2
4th 0.8 1.6
5th 1.1 2.2
6th 1.4 2.8
7th 1.8 3.7
8th 2.5 5.0
9th 3.1 6.2
10th 3.6 7.3
11th 5.0 9.9
12th 6.2 12.5
Reverse
R1 0.4 0.8
R2 1.0 1.9
R3 2.1 4.3
R4 4.3 8.6

Notes:
1 The manual prints the lift pump capacity as “7.3 U.S. gpm” and “6.5 Imp. gpm”. 7.3 U.S. gallons converts to about 6.1 Imperial gallons, so one of the two figures is a misprint. Transcribed exactly as printed. Verify against a clean copy.
2 The front wheel bearing grease specification is printed as “IT M1C-137-B”; the leading “IT” appears to be a printing artifact, and the specification is M1C-137-B.
3 The manual refers to a commercial oil chart “in the following chart”, but the chart does not appear on the specifications pages of this copy.
4 The two-wheel drive steering wheel height is printed as “61.1 in. (156.5 cm)”. 61.1 in. converts to about 155.2 cm, and 156.5 cm to about 61.6 in., so one figure is a misprint. Transcribed exactly as printed.
5 The manual presents ground speeds as a bar chart rather than a table. The values above are the endpoint figures printed on that chart at 1250 and 2500 rpm. They are transcribed, not measured from the graph.
All specifications transcribed from the specifications section of the Ford 1910 operator's manual, manual code SE 4096B, originally published by Ford. Production years, builder and series are from TractorData and are not printed in the manual. Ford reserved the right to change specifications without notice; verify against your tractor's serial number before ordering parts or setting clearances.

Need the complete Ford 1910 operator's manual?

Get the full 68-page manual as an instant PDF download: controls and instruments, operating procedures, tread settings and weighting, separate 2WD and 4WD service schedules, and the specification section reproduced above.

Download the Operators Manual

Other Ford compact tractors covered on this site:

Doing teardown work? The Ford 1910 & 2110 service repair manual covers overhaul procedures, clearances and torque values.

For how the 1910 compares with every other Ford compact, see Ford Compact Tractors: Every Model Compared.

Browse All Ford Tractor Manuals

All Ford specifications

Manual code: SE 4096B

Specifications last reviewed